l9820 high side driver operating supply voltage up to 25v dc current 0.3a r on < 800m w diagnostic and protection func- tions m p compatible enable input for stand-by mode description the l9820 high side driver realized with mul- tipower - bcd mixed technology, drives resistive or inductive loads with one side connected to ground. the enable input is ttl compatible and a diag- nostic output provides an indication of short circuit and device status (thermal and overvoltage shut- down). onchip thermal protection and short circuit protection are provided. september 2013 ? block diagram minidip s o8 ordering num bers: l9820 l9820d multipower bcd technology 40m w 1/6
absolute maximum ratings symbol parameter value unit v s max forward voltage 50 vdc i r reverse bias current at -1.3v ?0.46 a v 5 input voltage (to gnd) ?0.3 to 20 v v 8 diag. output voltage (to gnd) ?0.3 to 20 v v 1 output voltage (to gnd) ?0.3 to 25 v i 4 supply current internally limited i 5 enable input current 0.5 ma i 8 diag. out current (sink) 10 ma i 1 output current internally limited t op operation temperature ?40 to 85 c t j , t stg junction and storage temperature range ?55 to 150 c t jp detecting temperature 150 c thermal data symbol parameter minidip so8 unit r th j-amb thermal resistance junction-ambient max. 100 200 c/w truth table h: high level l: low level enable function diag. status power status l operating off h l h normal operation h h h overvoltage protection on l l h overcurrent protection on l l h overtemperature protection on ll pin connection (top views) minidip so8 l9820 2/6
pin functions n. name description 1 power output the device is provided with short circuit protection. 4 power supply supply voltage input. 5 enable input ttl comp atible input. high level on this pin means output current on. the low level voltage switches off the charge pump, the power stage and the diagnostic output reducing to the minimum value the quiescent current. 7 ground this pin must be connected to ground. 8 diagnostic feedback the diagnostic circuit is active in input high level condition. this output detects with tipically 50 m s delay at t amb = 25 c the following faults: ? overvoltage condition. ? thermal shutdown. ? short circuit. the power stage current is internally limited at 1.5a. the diagnostic output is active low. the diagnostic delay time allows to avoid spurious diagnosys(i.e.: turn on overcurrent, overvoltage spikes etc.). electrical characteristics (v s = 14.4v, ?40 c t j +85 c, unless otherwise specified.) symbol parameter test condition min. typ. max. unit v s operating supply voltage 6 25 v r on on resistance input > 2v, t j = 25 c input > 2v, full t range 0.6 0.8 1.2 w w i off off state supply current t j < 35 c t j = 85 c 130 300 m a m a i on on state supply current 4 ma v el enable low level 0.8 v v eh enable high level 2 v i e enable current 0v < vi <5v 10 m a i leakd diagnostic output leakage current v cc = 5v diagnostic output high 10 m a v satd diagnostic output saturated voltage isink < 3.5ma 0.4 v t dd diagnostic delay time t j = 25 c30 m s t don output on delay time t j = 25 c30 m s t r output on rise time tj = 25 c 100 m s t doff output off delay time tj = 25 c80 m s t f output off fall time tj = 25 c 100 m s v don overvoltage detection on 25 v v dh overvoltage hysteresis 2 5 v i don overcurrent detection on 0.5 1.5 a t don overtemperature detection on 150 c t dh overtemperature hysteresis 25 50 c l9820 3/6
dim. mm inch min. typ. max. min. typ. max. a 1.75 0.069 a1 0.1 0.25 0.004 0.010 a2 1.65 0.065 a3 0.65 0.85 0.026 0.033 b 0.35 0.48 0.014 0.019 b1 0.19 0.25 0.007 0.010 c 0.25 0.5 0.010 0.020 c1 45 (typ.) d (1) 4.8 5.0 0.189 0.197 e 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 3.81 0.150 f (1) 3.8 4.0 0.15 0.157 l 0.4 1.27 0.016 0.050 m 0.6 0.024 s8 (max.) (1) d and f do not include mold flash or protrusions. mold flash or potrusions shall not exceed 0.15mm (.006inch). so8 outline and mechanical data l9820 4/6
outline and mechanical data dim. mm inch min. typ. max. min. typ. max. a 3.32 0.131 a1 0.51 0.020 b 1.15 1.65 0.045 0.065 b 0.356 0.55 0.014 0.022 b1 0.204 0.304 0.008 0.012 d 10.92 0.430 e 7.95 9.75 0.313 0.384 e2.54 0.100 e3 7.62 0.300 e4 7.62 0.300 f 6.6 0.260 i 5.08 0.200 l 3.18 3.81 0.125 0.150 z 1.52 0.060 minidip l9820 5/6
l9820 6/6 docid4283 rev 3 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a parti cular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems wi th product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, automotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or registered trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2013 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - sweden - switzerland - united kingdom - united states of america www.st.com
|
